When tackling the task of removing the fairing on your 1985 FXRT Harley Davidson, did you know that there are specific points where the fairing connects that might not be immediately visible?
Understanding these connection points is important, but there's more to think about. As you start the process, you'll need to carefully navigate through a series of steps to successfully detach the fairing.
Stay tuned to uncover the precise steps and precautions necessary for a smooth fairing removal experience on your classic Harley Davidson.
Key Takeaways
- Gather necessary tools like socket wrench and screwdrivers for fairing removal.
- Carefully disassemble side panels, windshield, and fairing assembly step by step.
- Disconnect electrical connections by unplugging headlight and turn signal wiring harness.
- Unbolt fairing from the frame by identifying and removing securing bolts.
Tools Required for Fairing Removal
To efficiently remove the fairing on a 1985 FXRT Harley Davidson, gather a socket wrench, Phillips screwdriver, and Allen wrench set as these tools are essential for the task. The specific socket sizes needed are 1/4', 5/16', and 3/8' for various bolts on the fairing. Begin by using the Phillips screwdriver to remove the screws that hold the fairing in place. Next, utilize the Allen wrench set to loosen the bolts securing the fairing brackets to the frame.
Having these tools ready and organized is important for a smooth fairing removal process on your 1985 FXRT Harley Davidson. Make sure to keep track of the screws and bolts you remove to ensure easy reassembly. By following these steps and using the correct tools, you can liberate your bike from its fairing efficiently. Remember, precision and attention to detail are key when handling the fairing removal on your Harley Davidson.
Removing Side Panels and Windshield
If you have successfully removed the glove box door flap and the two flange nuts from the clip studs, you're now ready to proceed with freeing the side panels and windshield of the fairing.
- Step 1: Turn the screws to free the assembly while holding the locknuts.
- Step 2: Discard the rubber washers on both sides.
- Step 3: Carefully lift and remove the side panels from the fairing structure.
- Step 4: Gently detach the windshield by unscrewing any remaining fasteners.
Disconnecting Electrical Connections
Disconnecting the electrical connections involves carefully unplugging the headlight plug and turn signal wiring harness located behind the fairing on your 1985 Fxrt Harley Davidson. Begin by identifying the headlight plug; gently press the guarantee clip and pull the plug apart. For the turn signal wiring harness, locate the connector and release any assurance mechanisms before separating the components. Take a moment to observe the routing of the wiring to guarantee proper reconnection later.
To facilitate reassembly, consider labeling or marking the wires accordingly. Treat the electrical connections with care to prevent any damage during this process.
If you own an Electra Glide, the steps for disconnecting the electrical connections remain the same. Ensure a smooth removal by handling the headlight plug and turn signal wiring harness delicately. By following these steps, you'll be one step closer to successfully removing the fairing on your Harley Davidson.
Unbolting the Fairing From the Frame
After disconnecting the electrical connections behind the fairing on your 1985 Fxrt Harley Davidson, the next step is to carefully locate and remove the 16 bolts that secure the fairing to the frame.
To unfasten the fairing from the frame effectively, follow these steps:
- Begin by identifying the bolts positioned above the glove boxes.
- Proceed to locate the bolts placed over the crash bar.
- Look for bolts that secure the fairing into the frame.
- Lastly, inspect behind the headlight for additional bolts securing the fairing.
Carefully removing these 16 bolts is important in separating the fairing from the frame without causing any damage. Make sure each bolt is taken out with precision to prevent any mishaps during the process.
Safely Removing the Fairing Assembly
To safely remove the fairing assembly from your 1985 FXRT Harley Davidson, carefully disassemble the components starting with the glove box door flap and the flange nuts on the clip studs. Begin by gently removing the glove box door flap to access the inner mechanisms. Then, using appropriate tools, loosen and remove the flange nuts attached to the clip studs securing the fairing cap in place. Exercise caution to prevent any damage to the fairing during this process.
Next, replicate the same procedure on the opposite side of the fairing assembly to guarantee symmetrical disassembly. Remember to discard the rubber washer as you progress through the removal steps. It's essential to keep track of all the components you remove to facilitate a smooth reassembly later on.
Following these detailed steps meticulously will enable you to liberate the fairing assembly from your 1985 FXRT Harley Davidson effectively and safely. This process empowers you to work on your motorcycle with confidence and precision.
Conclusion
To sum up, removing the fairing on your 1985 FXRT Harley Davidson requires precision and patience. By carefully disconnecting electrical connections, unbolting the fairing from the frame, and safely removing the assembly, you can successfully complete this task.
Remember to handle the fairing with care to avoid stress cracks and make sure a smooth removal process.
So, stay steady, skillful, and seize the opportunity to strip the fairing off your Harley!
