How to Turn off Harley Davidson Security System

Yearning to unlock the secrets of your Harley Davidson security system? Discover the hidden treasure that awaits as we reveal the key to turning it off.

disabling harley davidson security

Unlocking the secrets of your Harley Davidson security system is like finding the key to a hidden treasure. With a few simple steps, you can conquer the fortress and gain control over your motorcycle.

But wait, there's more to this story than meets the eye. Along the way, you'll discover the power of the ignition key, the art of entering the PIN, and the importance of not disturbing the beast.

So, gear up and get ready to embark on a journey that will unveil the mysteries of how to turn off your Harley Davidson security system.

Key Takeaways

  • The security system on a Harley-Davidson can be disarmed by locating the ignition switch and turning it to the 'ACC' position.
  • The security system controls can be found either as toggle switches or buttons with security system icons, and the owner's manual should be consulted for their specific location.
  • To enter the override code and disable the security system, the left turn signal switch should be held down while turning the ignition key to the on position.
  • It is important to verify that the security system is turned off by performing a system deactivation confirmation and checking all components before riding the motorcycle.

Disarming the Security System

To disarm the Harley Davidson Security System, simply follow these steps. First, locate the ignition switch on the left side of the handlebar. Insert the key and turn it to the 'ACC' position. This will activate the electrical system while keeping the engine off.

Next, locate the security system control module, which is usually located under the seat. Use your key to unlock the module and remove the cover. Inside, you'll find a series of wires and connectors. Look for the wire labeled 'security system disable' or a similar designation. Disconnect this wire by gently pulling it apart. This will effectively disable the security system.

Once the wire is disconnected, replace the module cover and lock it securely. Finally, turn the ignition switch to the 'OFF' position and remove the key. Your Harley Davidson security system is now disarmed, allowing you the freedom to start your bike without any hindrance.

Locating the Security System Controls

The location of the Harley-Davidson Smart Security system controls can typically be found on the handlebars or near the ignition switch. When looking for these controls, keep in mind the following tips:

  • Look for a small toggle switch or buttons with security system icons to identify the controls. These icons may include a padlock symbol or a key symbol, indicating the security system's functions.
  • Consult the motorcycle's owner's manual for specific information on the location of the security system controls. The manual will provide detailed instructions and illustrations to help you locate the controls accurately.
  • In some models, the security system controls may be integrated into the motorcycle's instrument panel or digital display. Take a closer look at these areas to see if the controls are hidden within the existing components.

If you're still unsure about the exact location of the security system controls, it's recommended to contact a Harley-Davidson dealership or service center for assistance. Their trained technicians can guide you through the process and help you find the controls with ease.

Entering the Override Code

You can start the process of entering the override code by locating the security system controls on your Harley-Davidson motorcycle. These controls are typically located on the left side of the handlebars, near the ignition switch.

Once you have found the controls, follow these steps to enter the override code and disable the security system.

First, make sure the ignition key is in the off position. Then, hold down the left turn signal switch. While holding the switch, turn the ignition key to the on position. You'll notice that the security light on the instrument panel starts to flash.

Next, you need to enter the override code. The code consists of a series of turns and button presses. Refer to your Harley-Davidson owner's manual to find the specific code for your model. Using the left turn signal switch, follow the instructions in the manual to enter the code.

Once you have entered the correct code, release the left turn signal switch. The security light should stop flashing, indicating that the security system has been disabled.

You can now start your motorcycle and enjoy the freedom of riding without the security system restricting your every move.

Verifying the System Is Turned off

Take the following steps to ensure the security system on your Harley-Davidson motorcycle has been successfully disabled:

  • Turn the ignition key to the ignition position to verify the system is turned off. This will allow you to proceed with the next steps and ensure that the system is ready for deactivation.
  • Hold both turn signal switches until you receive confirmation that the system is turned off. This is an important step as it ensures that the system recognizes the command to disable the security system. Keep holding the switches for a few seconds after turning the ignition to allow the system to process the request.
  • Enter the first digit of the PIN using the left switch and press the right switch to enter the number in memory. This step is crucial in verifying the system is turned off. It allows you to input the personal identification number (PIN) associated with your security system and ensures that the correct code is entered for deactivation.

Once you have completed these steps, it's essential to perform a one-minute walk around while the motorcycle warms up and you put on your gear. During this time, check all lights, turn signals, brake lights, and horn to ensure they're functioning properly. This final check confirms that the security system is turned off and that you're ready to hit the open road with peace of mind.

Troubleshooting Common Issues

To effectively troubleshoot common issues with the Harley Davidson security system, it is crucial to understand the alarm disarming process and familiarize yourself with the features of the system. By doing so, you'll be better equipped to handle any problems that may arise. Let's take a look at some common issues and how to troubleshoot them:

Common Issue Troubleshooting Tips
Making mistakes during the disarming process Double-check that you are following the correct steps outlined in the owner's manual. Take your time and ensure each step is done correctly. If you're still having trouble, consider resetting the system by disconnecting and reconnecting the battery.
Radio frequency interference Radio frequency interference can cause the security system to malfunction. To troubleshoot this issue, try moving away from any sources of interference, such as radio towers or other electronic devices. If the problem persists, consider installing a radio frequency filter to reduce interference.
Disabling the alarm on a street rod Disabling the alarm on a street rod is a dealer-only job. If you're looking to disable the alarm yourself, explore alternative methods such as disconnecting the alarm module or seeking assistance from a professional motorcycle technician.

Conclusion

Congratulations! You have successfully disarmed the Harley Davidson security system using the provided instructions.

Did you know that according to a recent study, over 50% of motorcycle thefts occur due to inadequate security measures?

By following these steps and keeping your security system activated, you're taking an important step towards protecting your valuable Harley Davidson from potential theft.

Stay vigilant and ride with peace of mind.

Leave a Comment